Monday, October 20, 2008

update 10/19

click on the thumbnails for big.



We finally gave up and drilled out the stuck nut on the strut brace. That might net us $50 from a Foxbody enthusiast. We originally wanted to get it out to be able to oil the cylinders and test if the engine would rotate. But we decided it didn't need to be done now since the test was quick and we'd have plenty of time to rebuild it or source a new engine later.



Ben from Terrafugia disassembling the steering column. It mostly went ok, but the instructions said we could pull the spline shaft free from the steering rack. This wasn't the case for us, so we undid the next U-joint towards the steering rack and pull everything up to that half of the U-joint through the firewall. Note for the FFR manual: there could be a lot of loose single wires that the steering column mounts could snag on, so make sure you have clearance before you try to tug it out. We still have to remove the sleeve around the steel column shaft, as the kit doesn't need it. Oh, and the U-joint half needs to go with the steering rack, not here. Just to stick to the instructions.



Steering wheel and column out of the car. Note CG's aftermarket tach and shift light. His speedo cable broke, so we'll have to buy one as a donor part for the kit.



The ECU. This was hell to get out because it was packed between the rollcage and the fender wall. It was a slow process of unsnapping plugs and unbolting the ground. This thing better still be working, dammit.



Shot of the opened up Mustang. When we first tried to do either the ECU or steering column, we found the tight bucket seats to be a huge pain to work around, so we unbolted those and took the doors off. Oh, and also removed those roll cage foam pads, since the zip ties ends kept stabbing us as we got in and out.



The Mustang is nice and boxy, so perfect to storing stuff on.



the racing seats with their covers removed. Not sure what the plan with these is. The kit came with some seats and harnesses of their own.



Steering column and brake pedal washers. We were halfway done with removing the brake booster and master cylinder and decided to call it a day. But we at least unhooked the brake pedal from the brake booster pushrod. The instructions emphasized remembering the order of washers and clips mating the pushrod to the pin on the brake pedal, so I drew a diagram and ziptied them in order.



Misc crap sitting on the intake manifold.

It was a good 3 hour session. We were pretty on target time budget-wise with the donor part removal steps, but didn't account for taking out the seats and doors.

Next steps, roughly in order:
- bleed out brake fluid before removing MC and brake booster (I don't think the instructions reminded us to do it)
- remove brakes
- remove brake booster and MC
- remove steering rack
- extract wiring harness (will be a royal pain in the ass)
- rear end, suspension elements, e-brake
- headers, engine and tranny

Tuesday, October 14, 2008

Delivery Day

On Tuesday 14-October we took delivery of the Factory Five kit. This was a really fun day, as I traveled to the Factory Five factory in Wareham, MA with a UHaul to pick up the kit.

The Factory Five World HQ is located in a somewhat non-descript facility at the end of the road in an industrial park. I was pretty sure I had arrived when I hit the cul-de-sac and the pavement was full of skid marks. This transporter pretty much gave it away too:


The showroom has really stunning examples of the various models sold by Factory Five. I was particularly excited to see the Type 65 Coupe close up. I’ve seen one running example of this car on the street (for about a minute as the guy motored away), and I’ve seen the Factory Five DVD. But it wasn’t until Tuesday that I actually put hands-on the car itself:



There was also an excellent example of the GTM Supercar. I’m very interested in building one of these some day. We’ll have to see how the Coupe build goes first, but the GTM is an amazing car.


I met with Jason Lavigne, who gave me a tour of the facility. It’s a very cool place – a combination of straightforward and sophisticated, industrial and high tech. Everybody there is fired up about cars and racing and downright friendly. Judging from all the build blogs out there Factory Five must be one of the most photographed factories in the country. Nobody seemed to mind as I snapped pictures during the tour.

Stack of main tubes for coupes:


Vehicle chassis on rotating frame:


Roadster bodies stacked up:


Aluminum panels ready for use. These are pre-shaped, with cut-outs, and ready to go:


Coupe dashboard panels:


Coupe doors under construction:


After touring the facility and meeting people at Factory Five it was finally time to meet the kit. It sounds corny, but seeing this sign attached to the body of my kit was really exciting:


Next it was time to load the kit into the truck. Here’s the stack of boxes on board:


Here is kit, on a rolling frame, ready to go on the truck:


When you pick up the kit the body is on the frame, and several of the aluminum panels are on the frame. The windshield and rear glass are taped onto the body. In order to load the car the guys removed the windscreen and rear glass, and then guided a boom into the cockpit. This allowed them to raise up the car by the roll hoop and put it in the truck.










Once I got the kit loaded, I headed back to the showroom to take some technical photos of the front suspension. As I looked around, Dave Smith (President and founder of Factory Five) wandered over and introduced himself. This led to a great discussion of chassis setup, car philosophy, etc. He showed me the Roush Coupe, which can be seen on the Factory Five web site photo gallery. Dave is a committed racer and passionate about cars, and really seems to enjoy his job. Meeting him was totally by chance and was pretty neat.

With the truck loaded up I stopped a nearby Lowes and bought some tie down straps to secure the chassis for the ride home. Then I headed for home to unload.

Meng and Marc came over to help unload the car. The photos we took of the off-loading process did not come out, which is unfortunate. Sufficient to say, however, you really want 4 (or maybe even 6) people to help out with the unloading process. The 3 of us struggled a bit, but ultimately we got the body off the chassis, the chassis into the garage and on stands, the boxes into the garage, and the body propped up on wood outside in the driveway.

Friday, October 3, 2008

Craftsman Tools

I mentioned in an earlier post that I had picked up some more tools for this build.  I used some gift cards and bought a Sears Craftsman 260 piece mechanics tool set.  It came with a "free" 3 drawer plastic tool box that I originally thought would be useless.  Instead I was pleasantly surprised.  Each of the 3 drawers is fully removable from the box, and holds the sockets and drivers for 1/4", 3/8", and 1/2" sized ratchets respectively.   The size of each socket is molded into the drawer which makes finding the right size easy.  Best of all, you can carry the drawer to the work site easily, which makes locating the right size socket while in an inconvenient location (like under the car) much simpler.

I've always been a fan of Sears tools, and this set continues to keep me a fan.  Now I just need a couple cabinets and a few more air tools and the shop will be well equipped.

Fun tearing down...

The team is starting to come together now as the delivery date for the kit draws near.  Meng and Marc came out tonight to look over the car and assess things. We've decided to continue with tear-down, and eventually focus on getting the engine to turn over.  Assuming it's a bad starter or other external gremlin, if we can get the motor to spin freely then any issues can probably be fixed while the engine is out of the car and on the stand.  

So we dug into the tear-down.  The car is up on stands and the hood has been removed, the chassis brace is all but off (and would be completely off if not for a stripped bolt - I need to run to Sears for a nut-breaking tool).  The biggest accomplishment of the evening was getting the fuel cell out of the car.  The car has a FuelSafe cell which fit in the existing mounting points (using customized straps provided by FuelSafe) and uses the existing filler neck.  The cell is heavy - probably 10-12 gallons of old gasoline in it.  We supported it with floor jacks, removed the straps, removed the filler, and carefully lowered the cell to the floor.  The cell is now outside the garage waiting to be drained.

With the fuel cell out of the car we can now turn our attention to removing the Panhard bar, which in turn will give us access to the rear end, which we need for new car.  Once the Panhard bar is out of the car we can also get access to the exhaust system, all of which needs to be removed.

All the various nuts, bolts, and pieces that have been removed are boxed or bagged, ready to go onto the new car or be sold for another project.  We'll have several good pieces to sell soon:  Panhard bar, chassis brace, heavy duty caster/camber plates, etc.

It felt really good to pick up some tools and do some work.  Even though it's just tear-down, which by nature is a dirty, messy process it was still fun.